Відео

Hello my friend, I have a similar problem, the difference is that my doors don't lock, they just unlock, after replacing it do I need to reprogram something, or just install the fuse box?

Surprised the MAF cleaning fixed it! The grams per minute didn’t seem too far off ( unless it was substituted values). Obviously disconnecting it confirmed it though. Thanks for sharing!

My 2003 suburban Z71 has same package. Front has mild air and rear is freezing. Checked refrigerant pressure and looks good. Will try adding more refrigerant to see what happens.

I’ve always felt MAF is like transmission flush if you clean it at proper intervals it will usually be fine. But if it starts malfunctioning it’s not going to help cleaning it

Is it the same Mitsubishi they modify? Like the engines are different

Thanks for the video, I’m here in Texas and won’t pass inspection with engine light off and a code for p0420. How can I fix the problem? Thank you.

Appreciate it bro. Yeah turbo diagnostic can be a pain in the butt sometimes

How much do you charge for that fix? Do Soul's have grounding issues? I see videos about adding extra ground wires. Mine shocks me when I get in and out.

Thanks for sharing! Looking forward to part 2.

Good to have a turbo problem There's not that many on UA-cam

Rob thanks for sharing . Let’s see what happens in part 3 . 👍

Did he say this was a salvage title car? Just wondering only 15k miles, it must have been in an accident.

I know this will be a good video so I liked ahead of time

I spent days looking for this info and your video sent me straight to my issue! Couldn’t find helpful info anywhere else! Very much appreciated!

Great job

It's the diode .I have the suzuki aerio sx 2003. .had the same problem .

It's on the right side of the funeral box in the engine compartment.

The sazuki has a diode .with out it the car won't start

Bought a 2001 E350 with Class B+ 21' RV Coach a year ago. It had this problem in both neutral and park both. Wiggle and it might start or usually but seemed to be getting worse. Seller said he was sending me a kit to fix it but it never arrived. Meantime have an appointment with a repair shop later this Sept. I'm probably sure he has the ability to fix it but watching this makes me wonder if I should order a bushing repair kit and the interlock repair kit too just to make sure parts are on hand when we take it in. Hubby a few years ago would have handled this himself but pushing upper 80's not as dexterous and nimble as he used to be. This is very helpful for insight into this problem and thanks for sharing.

Definitely should do more teaching videos

Thank you man, big help!

Good video don’t see too many on here about crv. I replaced my 02sensors checked wires. And almost always the check engine light turns on right away Maybe the previous owner fryed the ecu. I’ve always had that problem since I bought it

Is this considered the left side detection module?thanks

I found 2 broken wires at that exact bend area. !!!! thanks for the upload.

great video , very helpful ❤️👍

great video... it's was highly informative and very user friendly. from noobs to wrench heads a wonderful masterpiece. Thank you.

You are the best. Mine had a small moth. Cost me a $150 tow. Thank you so much.

I've got a 21 explorer st, just a few days ago the parking aid default came on. My question is where is the module located? I've replaced the 2 sensors that showed bad, and tried to reset the module using forscan, but it won't reset.

I have Camry 2007, doing issues with transmission like, not forward transmission work until little warm up. update can fix?

Thank you sir you fixed my car

Do you watch these videos after you shoot? Holding the camera close while doing something off camera isn't helpful

Thanks for the video. I have a 2011 X3 with a parasitic draw that I am about to go look for, and if it is something as simple as yours was, I'll just leave that fuse out.

I get that stuff then after its simple things like this they say are you going to charge me for that. I say yes I am.

Is there a link for the circuit? My turn signals work but the hazard signal doesn't

This is cool. I just did one today with the in608. There is almost no information on making Saab keys with autel. With autel, Read the 93cl66a eeprom, go to write key via dump and insert the eeprom. It will decode the pin automatically for you when you load in the eeprom. Programmed Amazon keys and the remote worked automatically.

Hi 2015 ats car first started with stability. Trak and traction control then started to idle rough and gear down rough pulled over turned off on nothing came back hour later came back misfire cylinder four changed sparks coils in all afterwards ran fine idled better then next morning came back Same codes idle rough wanted to dies realized Pcv lines were cracked changed both cleared codes traction back and stability rough idle again misfire four again

Hello, how are you? I have a problem with a 2012 Malibu. I had the wiring serviced, i.e. the engine harness, and after that the radio does not work. I had the fuses checked and did not find any noticeable fault.

Rob...2002 XL-7. 260k miles. Windows, sunroof and blower stopped working. Everything else works. All fuses checked good. Ordered some of that stabilant 22A contact enhancer. Should arrive in a few days. Fingers crossed. Those ProDemand electrical diagrams seem very good and easy to read.

Exact same problem 04 avalanche guess im gonna have to have it flashed

I have a2006 is250 been sitting for 8 months was running when parked decided to get it going again bought new battery for it now it would just crank won’t start change fuel pump check all the fuse all good what could be the problem do you have any idea I’m all ears thanks.

What was the problem. What part needed to be replaced

Great Video!! I just bought a Pathfinder myself and needed help diagnosing the A/C, so thank you!!

Hi,can I get that wiring diagram please?

For the algorithm because lol I don’t like Audi 😁

Great video

Ok so I have a 2010 jeep patriot 2.4l I changed the spark plugs, ignition coil, and injectors. I'm still having a misfire in cylinder 3 got to do some reading on it and it said it could be the pcm so I changed it. Still having he issues. I also changed the valve cover gaskets as cylinder 3 had a little oil on the spark plug. After doing all of this I noticed it's been white smoking until it warms up and it goes away. Is that the head gasket that's causing all of this?

Good job 👍

Thanks for the video!

That's alot smoke for sure. Can you use UV due with the baby oil? It might be a lot cheaper. Solid video as usual bro

What kind of oil is that for smoke machine? Is it special for machine or what?